
Spiral plate heat exchangers
Single-channel, self-cleaning design for fouling, loaded or viscous fluids. Nexson rates it three times more thermally efficient than tubular units.
- Temperature
- −100 to 500 °C
- Pressure
- Up to 100 bar
Two manufacturers in one group. Nexson designs and builds fully welded heat exchangers in France for refining, petrochemical, oil & gas and heavy industry. thermowave, the group's German brand, makes plate heat exchangers for refrigeration, HVAC, food & beverage, process and energy. Supplied and serviced in Malaysia by Flowmach Engineering.


Nexson Group is a French heat exchanger manufacturer based in Burgundy. It designs and builds high-performance heat exchangers that improve the energy efficiency of industrial systems: liquid-liquid, gas-liquid and gas-gas exchangers, and skids. Its customers are in oil and gas, petrochemicals, refining, agro-industry, heavy industry and the environment.
thermowave is the group's plate heat exchanger brand, based in Berga, Germany, since 1993. It configures each plate heat exchanger to the customer's specification in a wide range of materials, frame designs and sizes, and tests its products in-house. Its plant runs a 12,000-ton (60,000 kN) press and laser cutting for large, high-capacity plates.
Flowmach is authorised agent for Nexson and distributor for thermowave in Malaysia. We size and supply new units, and our PHE service team maintains and reconditions plate heat exchangers onshore and offshore.
Fully welded exchangers for high pressure, high temperature, fouling and corrosive service, in stainless steel, duplex, titanium and nickel alloys.

Single-channel, self-cleaning design for fouling, loaded or viscous fluids. Nexson rates it three times more thermally efficient than tubular units.

Square corrugated plates welded into a block with no gaskets between plates. Remove the four side panels for inspection or cleaning.

Circular welded plates in a cylindrical shell: openable (O), fully welded (W) or kettle reboiler (K). Used for condensation, evaporation and waste heat recovery.

Diffusion-bonded, photo-etched microchannels (0.1 to 2 mm) in a monolithic block, with a footprint up to 90% smaller than shell & tube. For sCO₂, hydrogen, LNG and nuclear.

Spirally wound tube bundles that exchange heat between several fluids in one shell and absorb differential expansion during rapid thermal cycles.

For sludge, biosolids, bitumen and other viscous or loaded fluids. RT handles particles up to 30 mm with low pressure drop; TT tubes clean without full disassembly.
The thermoline ranges (ECO, VARIO, PURE and PLUS) cover standard HVAC units through to specialised apparatus for industrial refrigeration, food, chemicals and energy.

Stamped plates sealed by gaskets matched to each fluid. Add or remove plates to change capacity after installation; handles very close temperature approaches.

Laser-welded plate pairs for the corrosive or high-pressure stream, gaskets on the other side for easy cleaning. Common in ammonia refrigeration and chemicals.

Two plates per wall with a vented space between. A leak shows outside instead of mixing the fluids. For drinking water, pharmaceuticals and food.

A laser-welded circular plate bundle in a cylindrical shell. Leak-tight under high pressure and thermal shock, and much smaller than an equivalent shell & tube unit.
Spiral, welded plate and plate & shell units for fouling crude service, reboilers, condensers and offshore waste heat recovery.
Cooling for power generation, distribution and conversion, plus PCHE and coil wound units for hydrogen, LNG and sCO₂.
Corrosion-resistant plate heat exchangers for ammonia and other natural refrigerants, thermowave's founding market.
Heating feeds to reaction temperature and removing heat from exothermic reactions, in alloys matched to the media.
GREENTUBE RT and TT exchangers for sludge-to-sludge heat recovery and biosolids treatment.
Gasketed and double-wall plate heat exchangers for district heating and cooling, data centres, dairy and beverage plants.
Both brands back their equipment with certified spare parts, traceability and a global service team. In Malaysia, Flowmach's PHE team is on site.
Flowmach PHE servicingBoth manufacturers publish brochures and product pages on their websites. Or ask us for a thermal design for your duty.
Send your process data: fluids, flow rates, inlet and outlet temperatures, allowed pressure drop and design pressure. For spares, send the unit nameplate. Our engineers reply with a quotation, normally within two working days.